7.5. PNF Plug and Play¶
7.5.1. PNF Plug and Play¶
The following are the requirements related to PNF Plug and Play.
The PNF Vendor MAY provide software version(s) to be supported by PNF for SDC Design Studio PNF Model. This is set in the PNF Model property software_versions.
The following VES Events SHOULD be supported by the PNF: pnfRegistration VES Event, HVol VES Event, and Fault VES Event. These are onboarded via he SDC Design Studio.
Note: these VES Events are emitted from the PNF to support PNF Plug and Play, High Volume Measurements, and Fault events respectively.
The PNF MUST support & accept the provisioning of an ONAP contact IP address (in IPv4 or IPv6 format).
Note: For example, it a possibility is that an external EMS would configure & provision the ONAP contact IP address to the PNF (in either IPv4 or IPv6 format). For the PNF Plug and Play Use Case, this IP address is the service provider’s “point of entry” to the DCAE VES Listener.
Note: different service provider’s network architecture may also require special setup to allow an external PNF to contact the ONAP installation. For example, in the AT&T network, a maintenance tunnel is used to access ONAP.
The PNF MUST have “ONAP Aware” software which is capable of performing PNF PnP registration with ONAP. The “ONAP Aware” software is capable of performing the PNF PnP Registration with ONAP MUST either be loaded separately or integrated into the PNF software upon physical delivery and installation of the PNF.
Note: It is up to the specific vendor to design the software management functions.
If the PNF set up a TLS connection and mutual (two-way) authentication is being used, then the PNF MUST provide its own X.509v3 Certificate to the DCAE VES Collector for authentication.
Note: This allows TLS authentication by DCAE VES Collector.
Note: The PNF got its X.509 certificate through Enrollment with an operator certificate authority or a X.509 vendor certificate from the vendor factory CA.
Note: In R3 three authentication options are supported:
- HTTP with Username & Password and no TLS.
- HTTP with Username & Password & TLS with two-way certificate authentication.
- HTTP with Username & Password & TLS with server-side certificate authentication.
The PNF MUST use a IP address to contact ONAP.
Note: it is expected that an ONAP operator can ascertain the ONAP IP address or the security gateway to reach ONAP on the VID or ONAP portal GUI.
Note: The ONAP contact IP address has been previously configured and provisioned prior to this step.
Note: The ONAP IP address could be provisioned or resolved through FQDN & DNS.
The VNF or PNF MUST support a HTTPS connection to the DCAE VES Event Listener.
The PNF MUST support sending a pnfRegistration VES event.
The PNF MUST send the pnfRegistration VES event periodically.
The pnfRegistration VES event periodicity MUST be configurable.
Note: The PNF uses the service configuration request as a semaphore to stop sending the pnfRegistration sent. See the requirement PNP-5360 requirement.
If the PNF encounters an error authenticating, reaching the ONAP DCAE VES Event listener or recieves an error response from sending the pnfRegistration VES Event, it MAY log the error, and notify the operator.
Note: the design of how errors are logged, retrieved and reported will be a vendor-specific architecture. Reporting faults and errors is also a vendor specific design. It is expected that the PNF shall have a means to log an error and notify a user when a fault condition occurs in trying to contact ONAP, authenticate or send a pnfRegistration event.
The PNF MUST support one of the protocols for a Service Configuration message exchange between the PNF and PNF Controller (in ONAP): a) Netconf/YANG, b) Chef, or c) Ansible.
Note: The PNF Controller may be VF-C, APP-C or SDN-C based on the PNF and PNF domain.
When the PNF receives a Service configuration from ONAP, the PNF MUST cease sending the pnfRegistration VES Event.
The PNF MAY support the optional parameters for Service Configuration Parameters.
Note: These are detailed in the Stage 5 PnP
Note: These parameters are optional, and not all PNFs will support any or all of these parameters, it is up to the vendor and service provider to ascertain which ones are supported up to an including all of the ones that have been defined. Note: It is expected that there will be a growing list of supported configuration parameters in future releases of ONAP.
(Error Case) - If an error is encountered by the PNF during a Service Configuration exchange with ONAP, the PNF MAY log the error and notify an operator.
(Error Case) - The PNF MUST support a configurable timer to stop the periodicity sending of the pnfRegistration VES event. If this timer expires during a Service Configuration exchange between the PNF and ONAP, it MAY log a time-out error and notify an operator.
Note: It is expected that each vendor will enforce and define a PNF service configuration timeout period. This is because the PNF cannot wait indefinitely as there may also be a technician on-site trying to complete installation & commissioning. The management of the VES event exchange is also a requirement on the PNF to be developed by the PNF vendor.